My Cart: 0 item(s)

Product Search

Secure Checkout
CURRENT LEAD TIMES
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
Purchase Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
  • SKU: 1TS-UTK
    Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK

  • ★★★★★ ★★★★★ 4.33/5 Stars. (15 Reviews)
  • JCR Direct:
    $529.00
    Now:
    $476.10

    Free Shipping!

    Weight: 25.0 (lbs)

    Quantity in Basket:  None



Jeep 1 Ton Steering Upgrade.
Available for all makes and models of Jeeps.

Looking to upgrade your stock Jeep steering? Is your lifted Jeep having alignment problems? With our Jeep 1 ton steering upgrade, you eliminate the hard to adjust "Y" stock steering, it allows for a longer drag link to help with your steering angles, and most importantly gives you heavy duty steering that will take a beating and hold up to the off-road abuse.

The rods are a beefy 1.25" diameter DOM, with an almost .25" wall; threads are direct tapped into the tube. This means (unlike a threaded insert) the TRE has full thread engagement into the tube for the length of its threads. On this system the passenger side TRE dust boot is replaced with a polyurethane spacer, which pulls the body of the TRE against this knuckle. This eliminates the tie rod roll that an inverted T setup sometimes has.

While we have had great luck not running a steering stabilizer, if you really have to have one feel free to order this bracket kit from summit racing. This kit will still allow you to easily align our steering setup.

We recommend having this kit installed by a professional 4x4 shop in your area as drilling and reaming needs to be done to knuckles and pitman arm to fit the 1 ton tie rod ends. Installation should take about 2 hours.

Please read the installation instrucions below BEFORE BUYING THIS PRODUCT. This will ensure that you realize what is involved with this install, and the limitations of this setup. Any aftermarket diff guards/covers may need to be modified or replaced depending on their standoff compared to the stock cover. Most half guards (Like the Warn Diff cover) can easily be modified to fit.

Resources for drill bits/reamers...
Mcmaster-Carr drill 5/8" bit #2933A28 (direct link)
Speedway Motors - 1 1/2 Inch Per Foot Reamer(direct link)

 

Looking for answers to common questions about us or our products? See our FAQ here.

19 Questions asked on Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK

Ask us anything



Q charles • 04/16/2020, 2:44:18 PM will this kit work with a 5.5in lift?
A 04/16/2020, 5:17:11 PM Yes, but we recommend over the knuckle for that much lift.
Q matt • 05/15/2020, 4:05:06 PM Does you utk kit require you to run wheels with backspacing or can i use stock wheels
A 05/19/2020, 2:30:30 PM 15" stock backspace wheels may hit the tie rod ends.
Q Josh s. • 08/23/2020, 11:01:04 PM I have a 4.5 lift kit, and it says this will fit up to 4” will it still work with a added drop down pitman arm?
A 09/09/2020, 2:07:14 PM It will work, but angles start to get pretty steep of your trackbar and drag link. Drop brackets can help.
Q Scott • 09/09/2020, 0:55:27 AM Whats minimal lift height needed with the utk setup?
A 09/09/2020, 1:19:05 PM It will work with stock height vehicles in the UTK setup.
Q johnathan Velasco • 12/31/2020, 2:37:55 PM I have a 94 stock steering no lift will it fit with no problem or do I require a lift to make it fit??
A 01/07/2021, 1:01:36 PM It will fit.
Q Ken Amen • 02/26/2021, 0:58:00 AM This says it will fit all Jeeps is that including an '89 Jeep YJ bolt in? Any other modifications required?
A 03/01/2021, 2:42:00 PM This will not fit a YJ
Q Moises moraes • 05/30/2021, 2:00:18 PM I have a 3inch lift will this fit no problem?
A 06/04/2021, 11:31:41 AM Yes
Q Fernando • 06/01/2021, 3:00:00 AM Will this fit on a 1995 Jeep ZJ?
A 06/04/2021, 11:31:41 AM Yes
Q Jeffrey Buschard • 06/19/2021, 11:25:46 AM I have an 01 right hand drive XJ will this work with that some replacement parts I've found that aren't specifically made for RHD does not fit.
A 06/25/2021, 11:08:27 AM We have not tested with a right hand drive.
Q Captain black beard • 07/25/2021, 0:11:18 AM Will stock rims and back spacing work with this kit..?
A 08/12/2021, 2:32:10 PM Most stock wheels work fine UTK.
Q Joshua Kinard • 11/10/2021, 12:16:44 PM would this steering set up fit a 1997 tj with a 3" lift?
A 12/14/2021, 5:35:57 PM Yes, it would work for that.
Q Marshall • 01/08/2022, 12:11:49 PM What brand tie rod ends come with this kit? And what material is the steering links made of?
A 01/12/2022, 10:14:10 AM The tube is 1.25 DOM with at just under .250 wall. The TRE's are NAPA Proformer Chassis.
Q Jason • 01/20/2022, 6:31:42 AM I live in Australia, do you know if this kit is compatible with a RHD 96 xj
A 01/24/2022, 2:08:05 PM We have not tested with the RHD, not sure about drag link length.
Q Randall • 02/07/2022, 0:30:28 AM I have 4.5 inch lift on 33inch tires, 15 inch rims with 3.75 backspace. Will I have clearance issues?
A 02/11/2022, 3:56:46 PM Should be fine with that backspacing on the wheels.
Q Andrew • 03/13/2022, 8:33:01 PM I have a rusty's 8.5" lift on my xj, will this work on mine. I'm assuming I would have to mount on top of the knuckle.
A 04/06/2022, 12:43:58 PM The over the knuckle kit would be recommended at that lift height.
Q Morgan Meighen • 03/17/2022, 2:55:39 PM Will this allow room for a psc hyrdo assist ram on a LJ dana 44 with 4.5 lift.
A 04/06/2022, 12:43:58 PM Under would be the best bet, but it may require some custom fab to get it all to work together.
Q Thomas • 05/25/2023, 8:15:54 PM Is any drilling necessary for install?
A 06/22/2023, 4:47:32 PM Yes, please see product installation linked on product page.
Q Thomas Cruz • 11/15/2023, 12:02:20 PM it says it works with a 4 inch lift or higher. Will this work with a 3.5 inch lift? It's not quite 4... not quite 3.... but in the middle.
A 11/29/2023, 4:44:22 PM Yes, it would work with a 3.5 inch lift.
Q William Surrett • 03/27/2024, 7:59:45 PM Can you still run 15x8 rims on Cherokee XJ
A 04/17/2024, 5:35:16 PM Factory 15" rims should still work fine with this kit.
★★★★★ ★★★★★
4.33/5 Stars out of 15 Reviews
5
9
4
3
3
2
2
1
1
0
Pages 1   2
$800 to get it in Canada and didn't last
(Alberta) | August 19th, 2020
Kit comes with beefy rods but TREs were disappointing in their longetivity. Got 2500km out of them before they got play. Greasing didn't seem to help their durability either. Some decent Tres and they'd have a winning kit.
1 ton UTK steering
| February 15th, 2020
Kit is decent quality, nothing more than any other steering kit available! EXTREMELY over priced! Instructions left a few head scratching moments, had to call tech support for clarification about the bushing on the passenger side......then the tech I spoke with really didn't have any idea and made the comment that he wasn't really sure and was looking at the same thing I was with the instructions. After looking at another brand kit, got it figured out! Would I purchase this kit again?? NO, nor will recommend it. There is other options available that are the same quality for much less!!!!
Imported Review
| February 17th, 2017
Great setup, completely solved my death wabble.
Imported Review
| February 17th, 2017
"Great setup completely solved my death wabble."
Imported Review
| February 17th, 2017
Had bought this kit to upgrade my 01 xj with 4.5" of lift, my stock steering was falling apart, with this JCR UTK kit, it's 10x beafier and tighter. I absolutely love this kit, jcr had done it very well in this kit.
Imported Review
| February 17th, 2017
I bought this kit to run on a Cherokee with a 6.5 long arm lift with 35's. I read the reviews and the descriptions before buying it. And one thing that stood out was a steering stabilizer wasn't needed. I didn't believe it, but the kit installed easy and I'm at almost 5,000 miles with no stabilizer. I also received a call about a month after purchase. I didn't expect it, was asked how the kit was. How the install was and overall thoughts. I've never had anything like that when buying parts for my jeep. All part numbers for recommended tools was right. I love this kit. Would buy for another build in a heartbeat. Thanks JCR for a great product.
sdfgsfdg
| December 31st, 2016
asdfadsfadsf
Imported Review
| December 31st, 2016
"We installed this kit on my 1992 Jeep YJ with a 4" lift and 33" tires. It was an easy installation paying close attention to reaming the knuckles and getting the depths right. This was the 3rd kit that I had purchased for this Jeep I wont mention the other brands but they did not bolt up good and lost about 50% of the steering because they would hit the differential which is obviously unacceptable. This kit is extremely heavy duty and with the added dual stabilizer you just cant get better steering. If you want to save a ton of time trying to make other products work and end up with steering that is durable and most of all safe..........Here it is! "
Imported Review
| December 31st, 2016
We installed this kit on my 1992 Jeep YJ with a 4" lift and 33" tires. It was an easy installation paying close attention to reaming the knuckles and getting the depths right. This was the 3rd kit that I had purchased for this Jeep, I wont mention the other brands but they did not bolt up good and lost about 50% of the steering because they would hit the differential which is obviously unacceptable. This kit is extremely heavy duty and with the added dual stabilizer you just cant get better steering. If you want to save a ton of time trying to make other products work and end up with steering that is durable and most of all safe..........Here it is!
Best thought out 1-ton UTK Kit
(Redlands, CA) | October 18th, 2021
Great product, the use of 1.25" DOM tubing is probably what makes this kit better than all the others. Using straight-tubing allows for a much easier time setting toe. If you use 1.5" tubing it isnt going to clear the stock-trackbar hardware or an aftermarket diff-cover, hence the great choice in 1.25". The TRE's are the typical Moog parts, which will always be easy to source. Drilling out the knuckles and pitman arm can be a choir, easy with them removed and in a vise though. But I would rather have TRE's than heims when it involves a street-driven vehicle. I would have given this product a 5, but the QC leaves much to be desired. I never received the zerk fittings, cotter-pins or poly-bushing. And the real kicker was the castle-nuts, I got 3 out of 4. I had to go to the local junkyard because no part store carried one that would fit and Moog doesnt sell hardware.