My Cart: 0 item(s)
Wrangler Rear Bumper - JK dagger
JcrOffroad's Dagger Rear bumper gives the markets best rear departure angle, but still offers protection for the back of the body on the Jeep Wrangler JK.
- CNC cut and formed from 3/16" Steel.
- Requires Frame cutting and drilling.
- Includes (2) 3/4" thick shackle tabs.
- Built-in 2" receiver and safety chain cutouts.¹ ²
- Accepts aftermarket 3x3 LED Cube Lights.
- Includes mounting hardware.
- Includes JcrOffroad Sticker.
- Hand built in the USA!
¹ Concessions have been made for extra ground clearance and a sleek appearance and you will need to adjust your equipment accordingly. Depending on your setup this may mean longer drop hitches, wiring extensions, etc...
² Designed to support the loads of the factory tow capacity, but carries no SAE certification, nor is it designed to meet any DOT or FMCSA regulation.
We produce these products in a low volume compared to the OEMs or aftermarket receiver hitch companies. As such, it's not feasible for us to get this product tested against SAE J684 specifications or design it meet specific DOT or FMCSA regulations. So while we try to over-engineer our products with the loads of the factory vehicle capacity in mind; towing a trailer on public highways is at your own risk and we make no claims on the legality or viability of doing so. We cannot offer any recommendations on capacity beyond this. If the ratings of the factory receiver hitch are important to you, we would recommend choosing a bumper that keeps that in place.
Looking for answers to common questions about us or our products? See our FAQ here.
11 Questions asked on JK Rear Bumper | Dagger Stubby | Jeep Wrangler (07-18) •
Ask us anything
Q Preston Roebuck • 05/30/2020, 3:42:41 PM Can you run a 37” spare tire?
A 06/01/2020, 9:56:57 AM Depends on how you have your carrier setup. We would not recommend running a 37" on the stock carrier, but with a body mounted tire carrier it could fit fine.
Q Mike • 06/03/2020, 2:12:34 PM How difficult is it to put in a hitch pin and hook up the safety chains? Love the look of this bumper, but I pull a trailer.
A 06/03/2020, 4:21:01 PM The pin goes in behind the bumper, so it's a matter of kneeling on the ground and putting it in usually.
Q Matt Nicholson • 06/08/2020, 11:57:05 AM can you get one built with out the logo? I know it would take longer and that's ok.
A 06/10/2020, 4:19:49 PM No we can't, sorry.
Q Blake north • 08/09/2020, 0:42:34 AM The dagger rear bumper comes with (2) 1/2x13x 4” bolts. Your video or instructions don’t explain what they’re for, why are they supplied in this kit?
A 08/12/2020, 3:39:22 PM They are not used in this application.
Q JASON BYRD • 10/28/2020, 4:29:52 PM Will this work with the factory muffler or do you have to replace it?
A 11/03/2020, 3:33:15 PM Factory muffler is fine and is shown in the photos.
Q Mel • 12/29/2020, 2:41:50 AM Will this work on a JL? Or will you be making one for the JL? I like the idea of a fascia but also want it to extend to protect the pinch seams of the JL
A 12/30/2020, 4:42:59 PM We have no plans for this on the JL
Q Evan • 01/26/2021, 10:19:19 AM Does the bare metal take paint well when primed?
A 02/02/2021, 5:12:14 PM Yes, be sure to clean the metal with mineral spirits or similar first.
Q EO • 03/02/2021, 7:22:44 PM Can I get the dagger rear bumper with the receiver sticking out further so the pin hole is accessible? I like this bumper and will gladly give up that small bit of clearance for convenience.
A 03/08/2021, 12:20:24 PM Sorry, that is not a configuration we offer. This bumper was designed with max clearance in mind.
Q D Cassier • 03/10/2021, 3:15:34 PM Will this work with a factory tow hitch?
A 03/16/2021, 3:15:09 PM No, you would want the Crusader: JKRC (https://www.jcroffroad.com/product/JKRC.html)
Q Eddie Oh • 06/30/2021, 11:38:00 AM Can you still get this without the lightpod holes?
A 07/08/2021, 2:19:03 PM We only offer it with the light holes.
Q Jonathan Rowan • 07/01/2021, 4:19:06 PM Will this bumper work with a door mounted tire carrier?
A 07/08/2021, 2:19:03 PM As long as the back of the tire stuck off the gate far enough to clear the bumper face, yes.
Currently Viewing Reviews with a rating of 5. Click here to reset.
3
2
0
0
0
Deborah G (Rhode Island) | May 3rd, 2021
I ordered the bumper for my grandson for Christmas, because that is what he wanted me to buy him,because he loves his jeep. He is well satisfied good product. We will definitely order sgain. Thank you.
Anonymous | December 15th, 2016
This is an awesome looking, low profile bumper. Requires a little bit of cutting but is pretty straight forward. If you are contemplating cutting your frame, quit and just do it! the bumper mounted up nicely.
Anonymous | December 26th, 2017
This was the first thing I ever bought from JCR and it was perfect. The strength and optional textured powder coat is amazing and I bought this bumper for its high clearance low profile mounting and because I wasn't planning on running a spare tire on the back of the Jeep. It took a while to come in, but it the wait was well worth it for the product. I have since purchased much more from JCR because of their amazing customer service and well made products.
