My Cart: 0 item(s)
Cherokee Rear Bumper - XJ Crusader
JcrOffroad's Crusader Rear bumper is designed to provide maximum clearance with a streamlined design.
- CNC cut and formed from 3/16" Steel.
- Includes (2) 3/4" thick shackle tabs.
- Built-in 2" receiver and safety chain cutouts.¹ ²
- Accepts aftermarket 3x3 LED Cube Lights.
- Built in Hi-Lift Jacking points.
- Easy Bolt-on Installation.
- Includes mounting hardware.
- Includes Rear Unibody Tie-in Brackets
- Includes JcrOffroad Sticker.
- Hand built in the USA!
¹ Concessions have been made for extra ground clearance and a sleek appearance and you will need to adjust your equipment accordingly. Depending on your setup this may mean longer drop hitches, wiring extensions, etc...
² Designed to support the loads of the factory tow capacity, but carries no SAE certification, nor is it designed to meet any DOT or FMCSA regulation.
We produce these products in a low volume compared to the OEMs or aftermarket receiver hitch companies. As such, it's not feasible for us to get this product tested against SAE J684 specifications or design it meet specific DOT or FMCSA regulations. So while we try to over-engineer our products with the loads of the factory vehicle capacity in mind; towing a trailer on public highways is at your own risk and we make no claims on the legality or viability of doing so. We cannot offer any recommendations on capacity beyond this. If the ratings of the factory receiver hitch are important to you, we would recommend choosing a bumper that keeps that in place.
Looking for answers to common questions about us or our products? See our FAQ here.
1 Question asked on Jeep XJ Rear Bumper | Crusader | Jeep Cherokee (84-01) •
Ask us anything
Q Ramiro Gallegos • 07/31/2020, 10:03:03 PM Is it possible to mount flush LED's on the bumper? How are the measurements of the cavity opening?
A 08/05/2020, 12:41:14 PM You would have to cut the bumper and drill holes for that to work.
3
1
0
0
0
Shawn | December 11th, 2019
Good style, looks great. Unfortunately, I purchased this bumper with high hopes that weren't met. I purchased it without powdercoating and the welds were abysmal. They definitely were unfinished, and in some spots the panels weren't even welded together the entire length. Weld drip balls were all over. Nearly every weld had to be grinded down, and I had about 50% of it redone. I suspect I was accidentally sent it before it was complete, or before QA inspection.
Anonymous | April 4th, 2018
This bumper is heavy duty and well built. The receiver and d-rings are welded in very nicely. I feel very confident about towing with this bumper. I highly recommend getting the nut strips and new hardware to make installation much much easier. My rig had a stock nutstrip only on the passenger side and I broke two of those bolts while removing the stock bumper. The crusader definitely dresses up the rear of my XJ nicely. My only gripe is that no matter how adjusting and fine tuning I did the bumper ALWAYS stuck out farther past the body on the passenger than it did the driver's side. I've read on forums that this same thing has happened to others. I'm hoping the lower quarter panel armor I bought addresses this issue.
Anonymous | July 21st, 2018
A great product. The bumper is very well built, and fits the vehicle perfectly. I speak from experience when I say that this bumper looks great whether it is on the truck or buried three feet deep into the front of a Chrysler 300. What do you get when you combine two cars and a 55 mph collision? One totaled Chrysler, a bad off Cherokee, and a JCR Crusader bumper located under the floor. No worries though, that CNC cut, 3/16th thick steel was just fine, not even dented. The same could not be said for Jeeps unibody design. Nonetheless, a great product which is great for bouncing off rocks on the trails or stopping cars on the interstate.
Anonymous | December 31st, 2016
I highly recommend this product, JCR does great work. Everything aligned perfectly, and the welds are top-notch. Ive been pulled out by the D-ring mounts and the bumper help up great. I got it shipped in bare metal and painted it myself, it turned out great.
